DRIVERS FOR MINOLTA BIZHUB 500

Remove the screw [2] and then remove the filter cover [3]. Function to separate defective sections For setting of DipSW that is specified for the following items, it is possible to use them with a failed section sep- arated. Procedure Loosen the screw [1] and 2 screws [2]. Remove the harness clamp and unplug [22] the connector. Remove the ribbon cable [3]. Remove the Paper Output Tray. Remove the screw [18], and remove the lock release lever [19].

Uploader: Brasho
Date Added: 20 April 2015
File Size: 32.79 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 37880
Price: Free* [*Free Regsitration Required]

Overall control board 44 BN: Page 23 Classification Load symbol Ex. Remove the loop roller [3]. Remove two levers [6].

Printer: KONICA MINOLTA bizhub | OpenPrinting – The Linux Foundation

Page Following the instructions on the screen, check the folder to which an installation is made, and then click [Next]. And also, when the caution label is peeled off or soiled minolta bizhub 500 cannot be seen clearly, replace it with a new caution label. Remove the ribbon cable [3]. Remove the screw [2] and raise the fusing claw assy [3].

Toner for Konica Minolta Bizhub 500

Loosen the screw [3] and move the handle [4] in the arrow-marked bbizhub [5] to adjust the posi- tion of the punch unit [6].

New Drivers  MICROSOFT WIRELESS LASER KEYBOARD 5000 DRIVER

If cover and remove mode, minola original detection sensor there is paper jammed paper if any. Unplug two connectors [5]. Remove two screws [6] and remove the Feed Roller Cover [7]. Operation of each minolta bizhub 500 the output check modes 1 Sub tray paper exit mode The motor and the minolta bizhub 500 turn ON.

Weyehaeuser Recycled Laser Copy 20 lbs Metric: Remove the Right Door. Revision History Revision history After publication of this service manual, the parts and mechanism may be subject to change for improvement of minolta bizhub 500 performance.

Konica-Minolta bizhub 500 Parts Catalog

Remove the Conveyance Upper Cover. Remove the screw [2]. Remove the E-ring [3] and then remove the loop clutch CL2 [4].

Caution To enable this function, following conditions should be met. And, when replacing an intended minolta bizhub 500, the counter of the replaced part is reset to manage the service history. DC power supply 10 W: Loosen the screw [3] and slide the glass holding plate [4].

Go to main contents. After installing the bypass unit, open the tray 2 paper feed guide [1] and the bypass feed guide [2] in the arrow-marked direction minolta bizhub 500 to check to see if they operate smoothly.

New Drivers  PNY OPTIMA SDHC 4GB DRIVER FOR WINDOWS 10

Error Codes > Konica-Minolta > bizhub > page 1

Minolta bizhub 500 slit glass at the scanner section is coated, and therefore, its transmittance of the exposure lamp is different when compared to the original glass. Procedure Remove the screw mniolta and loosen the screw [2].

Remove the 2 screws [2] and then remove the paper roller cover [3]. Summary of Contents for Minolta bizhub 500 Minolta bizhub Page 1 Confidential — for internal use only, do not distribute Coat the cored bar section with grease.

Using a soft cloth dampened with alco- hol, wipe the Pick-up Roller [1]. Remove the back cover 6 screws. Repeat steps 1 and 2 and check the punch holes to see if the discrepancy “A” Everyprints 1. Move the bypass gate solenoid SD1 minolta bizhub 500 in the arrow-marked direction [3] and tighten the screw [1] when 50 length of “A” Minolta bizhub 500 paper is set, remove it.